← Back to All 330 Contractor Guides
Quarry Stone Grades (ASTM & DOT) Published 2026-10-21 8 min read By Burim Bekteshi · Senior Aggregate Editor

What Is ASTM #10 Stone Dust (Screenings)? Size, Weight per Cubic Yard & Best Uses

ASTM #10 Stone Dust (Screenings) is a standardized quarry aggregate screened to a particle size of 1/4"-Minus to #200 Dust (under 4.75 mm) with a loose bulk density of 1.48 tons/yd³ (2,960 lbs/yd³). Its primary engineering applications include: Dry-climate flagstone setting bed, bocce courts, horse stall bases, walkway compaction.

ASTM #10 Stone Dust (Screenings) gradation and density guide
ASTM #10 Stone Dust (Screenings) gradation and density guide
Quarry Specification Sheet · ASTM #10 Stone Dust (Screenings)
What size is ASTM #10 Stone Dust (Screenings) and how much does a cubic yard weigh?

ASTM #10 Stone Dust (Screenings) is a standardized quarry aggregate screened to a particle size of 1/4"-Minus to #200 Dust (under 4.75 mm) with a loose bulk density of 1.48 tons/yd³ (2,960 lbs/yd³). Its primary engineering applications include: Dry-climate flagstone setting bed, bocce courts, horse stall bases, walkway compaction.

Particle Size1/4"-Minus to #200 Dust (under 4.75 mm)
Bulk Density1.48 tons/yd³ (2,960 lbs/yd³)
100 Sq Ft @ 4" Deep~1.80 Tons (1.23 yd³)
Compaction Factor+12% to +15%

Specification & Reference Table: Coverage & Tonnage Chart for ASTM #10 Stone Dust (Screenings)

Project Area 2" Depth (Tons / Yds) 4" Depth (Tons / Yds) 6" Depth (Tons / Yds)
100 Sq Ft (10×10)0.91 T (0.68 yd³)1.82 T (1.36 yd³)2.73 T (2.04 yd³)
250 Sq Ft (10×25)2.28 T (1.70 yd³)4.55 T (3.40 yd³)6.83 T (5.09 yd³)
500 Sq Ft (10×50)4.55 T (3.40 yd³)9.11 T (6.79 yd³)13.66 T (10.19 yd³)
1,000 Sq Ft (20×50)9.11 T (6.79 yd³)18.22 T (13.58 yd³)27.33 T (20.37 yd³)

Bulk Density & Moisture Physics (ASTM #10 Stone Dust (Screenings)): When ordering quarry materials or scheduling dump truck dispatch, understanding the difference between loose cubic yard volume and certified scale tonnage is critical. Standard open-graded crushed stone (such as washed ASTM #57, #67, or #8 stone) maintains a loose bulk density of 2,640 to 2,720 lbs per cubic yard (1.32 to 1.36 US short tons/yd³) with a 38%–40% void ratio. Dense-graded road bases containing stone dust fines (such as #411 Crusher Run, #304 Limestone, Item #4, or Caltrans Class 2 AB) pack tighter and weigh 2,920 to 3,000 lbs per cubic yard (1.46 to 1.50 US short tons/yd³). After stockpile rain events, retained surface moisture can increase scale ticket weight by 5% to 12% on stone and up to 20% on sand or screened topsoil.

Loose vs. Compacted Volume (12%–18% Shrinkage Factor): Every cubic yard table measures in-place geometric volume before mechanical compaction. Once you spread aggregate and make 3 to 4 passes with a 5,000-lb vibratory plate compactor or smooth-drum roller, angular particles rotate into void spaces and the lift thickness compresses by 12% to 18% (and up to 20% for Decomposed Granite or Crusher Run). Regional mineralogy also shifts yield: dolomitic limestone and granite average 1.35–1.48 tons/yd³, dense Pacific Northwest basalt reaches 1.52 tons/yd³, and porous volcanic scoria or lava rock weighs just 0.65–0.78 tons/yd³.

Step-by-Step Tonnage, Volume & Cost Calculation

To eliminate mid-project material shortages or paying a second dump truck mobilization fee, professional estimators calculate takeoff quantities for ASTM #10 Stone Dust (Screenings) using three standardized civil engineering formulas:

Contractor Job-Site Takeoff Formulas (ASTM #10 Stone Dust (Screenings)):
1. Cubic Yards from Inches: Area (sq ft) × Compacted Depth (in) ÷ 324 = Net Cubic Yards (yd³)
2. US Short Tons Conversion: Net Cubic Yards × Bulk Density (1.35 to 1.48 tons/yd³) × 1.12 Compaction Factor = Order Tons
3. Total Delivered Price: (Order Tons × Quarry Price/Ton) + (Number of Truckloads × Haul Fee) = Total Delivered Cost

Worked Job-Site Example (600 Sq Ft Project @ 4" Compacted Depth): Suppose you are preparing a 12 ft × 50 ft (600 sq ft) area at a 4-inch compacted depth. Using the volume formula, 600 sq ft × 4 in ÷ 324 = 7.41 net cubic yards (200 cubic feet). Multiplying 7.41 yd³ × 1.42 tons/yd³ yields 10.52 net tons. Adding a 12% vibratory compaction and grading buffer brings your quarry order to 11.78 US short tons (8.30 cubic yards)—which fits cleanly inside a single 15-ton tandem-axle dump truck load. At a 2026 benchmark rate of $36/ton material ($424) plus a $155 local haul fee, total delivered job cost is $579 ($0.97 per sq ft).

Bulk Dump Truck Delivery vs. Buying 50-Lb (0.5 Cu Ft) Bags: Hardware store gravel, sand, and stone are sold in 50-lb bags containing 0.50 cubic feet. Because 1 cubic yard equals 27 cubic feet, it takes 54 bags to equal 1 cubic yard (and 40 bags to equal 1 US short ton). For the 8.30-cubic-yard example above, buying bagged stone would require 448 individual 50-lb bags costing $2,240+ at $5.00/bag—nearly 4× more expensive than a single $579 bulk dump truck drop. Bulk delivery beats bagged material on every project exceeding 1.5 tons (60 bags).

Material Grade Comparison & Contractor Installation Best Practices

Selecting the right aggregate gradation and sub-base assembly determines whether your installation stays laser-level for 20 years or ruts and pumps mud after the first freeze-thaw season. Compare the four primary contractor aggregate classes below:

Aggregate Class & Grade Bulk Density Compaction Buffer Optimal Lift Depth & Geotextile Pairing Primary Engineering Application
Dense-Graded Base (#411, #304, Item #4, Class 2 AB) 1.48 – 1.50 T/yd³ +15% 4"–6" lifts over woven stabilization fabric Driveway structural base, paver sub-base, parking lots
Open-Graded Washed Stone (ASTM #57, #67, #4) 1.32 – 1.36 T/yd³ +10% 3"–4" layer wrapped in 4 oz non-woven fabric French drains, shed pads, retaining wall backfill, concrete slabs
Fine Screed & Pathway Stone (#8, #89, Pea Gravel, DG) 1.32 – 1.46 T/yd³ +12% – 18% 1"–3" compacted or screeded top lift Patio walkways, permeable paver bedding, xeriscape beds
Heavy Sub-Base & Armor (#1, #2, #3 Ballast, Riprap) 1.28 – 1.30 T/yd³ +10% 6"–12" lift over heavy woven geotextile Soft clay stabilization, construction entrances, ditch erosion armor
  • Sub-Base Excavation & Organic Stripping: Always strip 100% of sod, roots, and spongy black topsoil down to firm mineral subsoil. Topsoil decomposes and holds water, causing gravel layers to sink unevenly.
  • Woven vs. Non-Woven Geotextile Fabric Selection: Roll out high-tensile woven stabilization geotextile (200–300 lb grab tensile) under driveways, parking pads, and road bases to separate clay from crushed stone. Use 4 oz to 6 oz needle-punched non-woven drainage fabric inside French drain trenches and behind retaining walls where high water permittivity is required.
  • Compaction in 4-Inch Maximum Lifts: Never dump 8 to 12 inches of Crusher Run or road base and attempt to compact it in a single pass. Spread and compact in 3-inch to 4-inch lifts at optimum moisture content (lightly misted with a garden hose so stone dust binds tightly without turning soupy).
  • Positive Drainage Slope & Edge Restraint: Grade driveways with a 2% to 3% center crown (1/4" to 3/8" drop per foot toward side ditches) and pitch patios 1/8" to 1/4" per foot away from building foundations. Secure decorative pea gravel or decomposed granite with steel, aluminum, or timber perimeter edging.
  • Common Ordering Mistakes to Avoid: Never order washed #57 stone for a steep sloped driveway without a compacted #304/#411 base (clean stone rolls on grades over 6%), never exceed half-ton pickup axle payload limits (1 cubic yard = 2,700 lbs), and always verify overhead tree/wire clearance (24–28 ft raised bed height) before dump truck arrival.
Quarry Order Calculator

Calculate Exact Tons of ASTM #10 Stone Dust (Screenings)

Enter your project dimensions to get instant tonnage, cubic yards, and dump truck load counts.

Frequently Asked Questions

How do you calculate exact tons and cubic yards for ASTM #10 Stone Dust (Screenings)?
Multiply your project length (ft) × width (ft) × depth (ft) and divide by 27 to get net cubic yards (yd³), or use the contractor shortcut Area (sq ft) × Depth (in) ÷ 324 = Cubic Yards. Multiply cubic yards by the material bulk density (1.35 tons/yd³ for washed #57 or pea stone; 1.48 tons/yd³ for Crusher Run or road base) and add a 10% to 15% compaction buffer.
How much area does 1 ton or 1 cubic yard cover for ASTM #10 Stone Dust (Screenings)?
One cubic yard (27 cu ft) covers 324 sq ft at 1" deep, 162 sq ft at 2" deep, 108 sq ft at 3" deep, 81 sq ft at 4" deep, and 54 sq ft at 6" deep. Because 1 US short ton (2,000 lbs) of standard gravel equals approximately 0.74 cubic yards (20 cu ft), 1 ton covers 120 sq ft at 2" deep, 80 sq ft at 3" deep, or 60 sq ft at 4" deep.
What compacted lift depth and geotextile fabric are recommended for ASTM #10 Stone Dust (Screenings)?
For walkways, landscape beds, and surface top-dressing, install 2 to 3 inches over non-woven landscape fabric. For shed pads, paver patio bases, and residential driveways, install 4 to 6 inches compacted in 3"–4" lifts with a vibratory plate compactor over a woven stabilization geotextile membrane. Heavy truck aprons and clay subgrades require an 8 to 12 inch multi-layer sub-base.
How much does bulk dump truck delivery cost compared to 50-lb bags in 2026?
In 2026, bulk quarry aggregate costs $26 to $55 per ton ($35 to $75 per cubic yard) plus a $125 to $195 dump truck delivery fee, putting a full 15-ton tandem dump truck load at $450 to $750 delivered. By contrast, buying 50-lb (0.5 cu ft) retail bags requires 54 bags per cubic yard (40 bags per ton) at $4.50–$6.50 per bag—costing $180 to $260 per ton. Bulk delivery is cheaper for any order above 1.5 to 2.0 tons.
PRO CONTRACTOR & HARDSCAPE TAKEOFF BUNDLE EXCEL (.XLSX) + GOOGLE SHEETS

Need Multi-Layer Takeoffs, Client PDF Proposals & Job Costing in Excel / Google Sheets?

Upgrade to the Pro Excavation, Hardscape & Aggregate Bid Workbook (Excel + Google Sheets)—engineered for contractors, landscapers, and estimators who want instant multi-layer assemblies, dirt spoils hauling math, crew labor markups, and printable client bid sheets.

01. Multi-Layer Driveway & Patio Assembly Takeoff
02. Excavation Spoils & Dump Truck Hauling Optimizer
03. French Drain & Retaining Wall Calculator
04. Crew Loaded Labor & Overhead Markup Calculator
05. Quarry & Supplier Price Book (VLOOKUP)
06. Client-Ready Printable Bid Proposal
07. Material Order & Dispatch Checklist
08. 12-Month Job Costing & Profit Tracker
$24 One-Time Download
Unlocked Formulas
Download Pro Workbook ($24) →
Works in Microsoft Excel, Google Sheets & Apple Numbers
Topics: astm #10 stone dust (screenings), quarry stone sizes, astm aggregate chart
Open Quarry Stone Calculator →

Related Quarry Stone Grades (ASTM & DOT) Guides

Quarry Stone Grades (ASTM & DOT)

What Is ASTM #1 Crushed Stone? Size, Weight per Cubic Yard & Best Uses

ASTM #1 Crushed Stone measures 1.5" to 3.5" (38–90 mm) and weighs 1.28 tons/yd³ (2,560 lbs/yd³). Learn where contractors use ASTM #1 Crushed Stone and calculate exact tons and cubic yards.

Quarry Stone Grades (ASTM & DOT)

What Is ASTM #2 Crushed Stone? Size, Weight per Cubic Yard & Best Uses

ASTM #2 Crushed Stone measures 1.5" to 2.5" (38–63 mm) and weighs 1.30 tons/yd³ (2,600 lbs/yd³). Learn where contractors use ASTM #2 Crushed Stone and calculate exact tons and cubic yards.

Quarry Stone Grades (ASTM & DOT)

What Is ASTM #3 Stone (Railroad Ballast)? Size, Weight per Cubic Yard & Best Uses

ASTM #3 Stone (Railroad Ballast) measures 1.0" to 2.0" (25–50 mm) and weighs 1.30 tons/yd³ (2,600 lbs/yd³). Learn where contractors use ASTM #3 Stone (Railroad Ballast) and calculate exact tons and cubic yards.

Quarry Stone Grades (ASTM & DOT)

What Is ASTM #4 Crushed Stone? Size, Weight per Cubic Yard & Best Uses

ASTM #4 Crushed Stone measures 3/4" to 1.5" (19–38 mm) and weighs 1.32 tons/yd³ (2,640 lbs/yd³). Learn where contractors use ASTM #4 Crushed Stone and calculate exact tons and cubic yards.

Quarry Stone Grades (ASTM & DOT)

What Is ASTM #5 Crushed Stone? Size, Weight per Cubic Yard & Best Uses

ASTM #5 Crushed Stone measures 3/8" to 1.0" (9.5–25 mm) and weighs 1.34 tons/yd³ (2,680 lbs/yd³). Learn where contractors use ASTM #5 Crushed Stone and calculate exact tons and cubic yards.

Quarry Stone Grades (ASTM & DOT)

What Is ASTM #57 Crushed Stone? Size, Weight per Cubic Yard & Best Uses

ASTM #57 Crushed Stone measures 1/2" to 1.0" (12.5–25 mm) and weighs 1.35 tons/yd³ (2,700 lbs/yd³). Learn where contractors use ASTM #57 Crushed Stone and calculate exact tons and cubic yards.