← Back to All 330 Contractor Guides
Material Comparisons Published 2026-10-23 8 min read By Burim Bekteshi · Senior Aggregate Editor

Screened Topsoil vs. Garden Loam / Planting Mix: Density, Cost & Best Uses Compared (2026 Guide)

Structural & Base Winner: Screened Topsoil for grading & lawn leveling; Garden Loam for raised beds. Surface & Landscaping Winner: 50/50 Blend for new sod installation. When ordering in bulk, Screened Topsoil weighs 1.08 T/yd³ ($28–$45/yd³), whereas Garden Loam / Planting Mix weighs 0.95 T/yd³ ($36–$58/yd³).

Screened Topsoil vs Garden Loam / Planting Mix comparison chart
Screened Topsoil vs Garden Loam / Planting Mix comparison chart
Head-to-Head Material Comparison · Quick Answer
Screened Topsoil vs. Garden Loam / Planting Mix: Density, Cost & Best Uses Compared: Which is better for your project?

Structural & Base Winner: Screened Topsoil for grading & lawn leveling; Garden Loam for raised beds.
Surface & Landscaping Winner: 50/50 Blend for new sod installation.
When ordering in bulk, Screened Topsoil weighs 1.08 T/yd³ ($28–$45/yd³), whereas Garden Loam / Planting Mix weighs 0.95 T/yd³ ($36–$58/yd³).

Screened Topsoil Density1.08 T/yd³
Garden Loam / Planting Mix Density0.95 T/yd³
Screened Topsoil Price$28–$45/yd³
Garden Loam / Planting Mix Price$36–$58/yd³

Specification & Reference Table: Engineering & Pricing Comparison: Screened Topsoil vs. Garden Loam / Planting Mix: Density, Cost & Best Uses Compared

Specification Screened Topsoil Garden Loam / Planting Mix
Bulk Density / Spec 1.08 T/yd³ 0.95 T/yd³
Typical 2026 Quarry Price $28–$45/yd³ $36–$58/yd³
Best Structural Use Screened Topsoil for grading & lawn leveling; Garden Loam for raised beds
Best Surface / Foot Traffic Use 50/50 Blend for new sod installation

Bulk Density & Moisture Physics (Screened Topsoil vs. Garden Loam / Planting Mix: Density, Cost & Best Uses Compared: Density, Cost & Best Uses Compared): When ordering quarry materials or scheduling dump truck dispatch, understanding the difference between loose cubic yard volume and certified scale tonnage is critical. Standard open-graded crushed stone (such as washed ASTM #57, #67, or #8 stone) maintains a loose bulk density of 2,640 to 2,720 lbs per cubic yard (1.32 to 1.36 US short tons/yd³) with a 38%–40% void ratio. Dense-graded road bases containing stone dust fines (such as #411 Crusher Run, #304 Limestone, Item #4, or Caltrans Class 2 AB) pack tighter and weigh 2,920 to 3,000 lbs per cubic yard (1.46 to 1.50 US short tons/yd³). After stockpile rain events, retained surface moisture can increase scale ticket weight by 5% to 12% on stone and up to 20% on sand or screened topsoil.

Loose vs. Compacted Volume (12%–18% Shrinkage Factor): Every cubic yard table measures in-place geometric volume before mechanical compaction. Once you spread aggregate and make 3 to 4 passes with a 5,000-lb vibratory plate compactor or smooth-drum roller, angular particles rotate into void spaces and the lift thickness compresses by 12% to 18% (and up to 20% for Decomposed Granite or Crusher Run). Regional mineralogy also shifts yield: dolomitic limestone and granite average 1.35–1.48 tons/yd³, dense Pacific Northwest basalt reaches 1.52 tons/yd³, and porous volcanic scoria or lava rock weighs just 0.65–0.78 tons/yd³.

Step-by-Step Tonnage, Volume & Cost Calculation

To eliminate mid-project material shortages or paying a second dump truck mobilization fee, professional estimators calculate takeoff quantities for Screened Topsoil vs. Garden Loam / Planting Mix: Density, Cost & Best Uses Compared: Density, Cost & Best Uses Compared using three standardized civil engineering formulas:

Contractor Job-Site Takeoff Formulas (Screened Topsoil vs. Garden Loam / Planting Mix: Density, Cost & Best Uses Compared: Density, Cost & Best Uses Compared):
1. Cubic Yards from Inches: Area (sq ft) × Compacted Depth (in) ÷ 324 = Net Cubic Yards (yd³)
2. US Short Tons Conversion: Net Cubic Yards × Bulk Density (1.35 to 1.48 tons/yd³) × 1.12 Compaction Factor = Order Tons
3. Total Delivered Price: (Order Tons × Quarry Price/Ton) + (Number of Truckloads × Haul Fee) = Total Delivered Cost

Worked Job-Site Example (600 Sq Ft Project @ 4" Compacted Depth): Suppose you are preparing a 12 ft × 50 ft (600 sq ft) area at a 4-inch compacted depth. Using the volume formula, 600 sq ft × 4 in ÷ 324 = 7.41 net cubic yards (200 cubic feet). Multiplying 7.41 yd³ × 1.42 tons/yd³ yields 10.52 net tons. Adding a 12% vibratory compaction and grading buffer brings your quarry order to 11.78 US short tons (8.30 cubic yards)—which fits cleanly inside a single 15-ton tandem-axle dump truck load. At a 2026 benchmark rate of $36/ton material ($424) plus a $155 local haul fee, total delivered job cost is $579 ($0.97 per sq ft).

Bulk Dump Truck Delivery vs. Buying 50-Lb (0.5 Cu Ft) Bags: Hardware store gravel, sand, and stone are sold in 50-lb bags containing 0.50 cubic feet. Because 1 cubic yard equals 27 cubic feet, it takes 54 bags to equal 1 cubic yard (and 40 bags to equal 1 US short ton). For the 8.30-cubic-yard example above, buying bagged stone would require 448 individual 50-lb bags costing $2,240+ at $5.00/bag—nearly 4× more expensive than a single $579 bulk dump truck drop. Bulk delivery beats bagged material on every project exceeding 1.5 tons (60 bags).

Material Grade Comparison & Contractor Installation Best Practices

Selecting the right aggregate gradation and sub-base assembly determines whether your installation stays laser-level for 20 years or ruts and pumps mud after the first freeze-thaw season. Compare the four primary contractor aggregate classes below:

Aggregate Class & Grade Bulk Density Compaction Buffer Optimal Lift Depth & Geotextile Pairing Primary Engineering Application
Dense-Graded Base (#411, #304, Item #4, Class 2 AB) 1.48 – 1.50 T/yd³ +15% 4"–6" lifts over woven stabilization fabric Driveway structural base, paver sub-base, parking lots
Open-Graded Washed Stone (ASTM #57, #67, #4) 1.32 – 1.36 T/yd³ +10% 3"–4" layer wrapped in 4 oz non-woven fabric French drains, shed pads, retaining wall backfill, concrete slabs
Fine Screed & Pathway Stone (#8, #89, Pea Gravel, DG) 1.32 – 1.46 T/yd³ +12% – 18% 1"–3" compacted or screeded top lift Patio walkways, permeable paver bedding, xeriscape beds
Heavy Sub-Base & Armor (#1, #2, #3 Ballast, Riprap) 1.28 – 1.30 T/yd³ +10% 6"–12" lift over heavy woven geotextile Soft clay stabilization, construction entrances, ditch erosion armor
  • Sub-Base Excavation & Organic Stripping: Always strip 100% of sod, roots, and spongy black topsoil down to firm mineral subsoil. Topsoil decomposes and holds water, causing gravel layers to sink unevenly.
  • Woven vs. Non-Woven Geotextile Fabric Selection: Roll out high-tensile woven stabilization geotextile (200–300 lb grab tensile) under driveways, parking pads, and road bases to separate clay from crushed stone. Use 4 oz to 6 oz needle-punched non-woven drainage fabric inside French drain trenches and behind retaining walls where high water permittivity is required.
  • Compaction in 4-Inch Maximum Lifts: Never dump 8 to 12 inches of Crusher Run or road base and attempt to compact it in a single pass. Spread and compact in 3-inch to 4-inch lifts at optimum moisture content (lightly misted with a garden hose so stone dust binds tightly without turning soupy).
  • Positive Drainage Slope & Edge Restraint: Grade driveways with a 2% to 3% center crown (1/4" to 3/8" drop per foot toward side ditches) and pitch patios 1/8" to 1/4" per foot away from building foundations. Secure decorative pea gravel or decomposed granite with steel, aluminum, or timber perimeter edging.
  • Common Ordering Mistakes to Avoid: Never order washed #57 stone for a steep sloped driveway without a compacted #304/#411 base (clean stone rolls on grades over 6%), never exceed half-ton pickup axle payload limits (1 cubic yard = 2,700 lbs), and always verify overhead tree/wire clearance (24–28 ft raised bed height) before dump truck arrival.
Interactive Material Estimator

Calculate Exact Tonnage for Screened Topsoil or Garden Loam / Planting Mix

Run your length, width, and depth in our calculator to compare total tons, cubic yards, and delivered cost.

Frequently Asked Questions

How do you calculate exact tons and cubic yards for Screened Topsoil vs. Garden Loam / Planting Mix: Density, Cost & Best Uses Compared: Density, Cost & Best Uses Compared?
Multiply your project length (ft) × width (ft) × depth (ft) and divide by 27 to get net cubic yards (yd³), or use the contractor shortcut Area (sq ft) × Depth (in) ÷ 324 = Cubic Yards. Multiply cubic yards by the material bulk density (1.35 tons/yd³ for washed #57 or pea stone; 1.48 tons/yd³ for Crusher Run or road base) and add a 10% to 15% compaction buffer.
How much area does 1 ton or 1 cubic yard cover for Screened Topsoil vs. Garden Loam / Planting Mix: Density, Cost & Best Uses Compared: Density, Cost & Best Uses Compared?
One cubic yard (27 cu ft) covers 324 sq ft at 1" deep, 162 sq ft at 2" deep, 108 sq ft at 3" deep, 81 sq ft at 4" deep, and 54 sq ft at 6" deep. Because 1 US short ton (2,000 lbs) of standard gravel equals approximately 0.74 cubic yards (20 cu ft), 1 ton covers 120 sq ft at 2" deep, 80 sq ft at 3" deep, or 60 sq ft at 4" deep.
What compacted lift depth and geotextile fabric are recommended for Screened Topsoil vs. Garden Loam / Planting Mix: Density, Cost & Best Uses Compared: Density, Cost & Best Uses Compared?
For walkways, landscape beds, and surface top-dressing, install 2 to 3 inches over non-woven landscape fabric. For shed pads, paver patio bases, and residential driveways, install 4 to 6 inches compacted in 3"–4" lifts with a vibratory plate compactor over a woven stabilization geotextile membrane. Heavy truck aprons and clay subgrades require an 8 to 12 inch multi-layer sub-base.
How much does bulk dump truck delivery cost compared to 50-lb bags in 2026?
In 2026, bulk quarry aggregate costs $26 to $55 per ton ($35 to $75 per cubic yard) plus a $125 to $195 dump truck delivery fee, putting a full 15-ton tandem dump truck load at $450 to $750 delivered. By contrast, buying 50-lb (0.5 cu ft) retail bags requires 54 bags per cubic yard (40 bags per ton) at $4.50–$6.50 per bag—costing $180 to $260 per ton. Bulk delivery is cheaper for any order above 1.5 to 2.0 tons.
PRO CONTRACTOR & HARDSCAPE TAKEOFF BUNDLE EXCEL (.XLSX) + GOOGLE SHEETS

Need Multi-Layer Takeoffs, Client PDF Proposals & Job Costing in Excel / Google Sheets?

Upgrade to the Pro Excavation, Hardscape & Aggregate Bid Workbook (Excel + Google Sheets)—engineered for contractors, landscapers, and estimators who want instant multi-layer assemblies, dirt spoils hauling math, crew labor markups, and printable client bid sheets.

01. Multi-Layer Driveway & Patio Assembly Takeoff
02. Excavation Spoils & Dump Truck Hauling Optimizer
03. French Drain & Retaining Wall Calculator
04. Crew Loaded Labor & Overhead Markup Calculator
05. Quarry & Supplier Price Book (VLOOKUP)
06. Client-Ready Printable Bid Proposal
07. Material Order & Dispatch Checklist
08. 12-Month Job Costing & Profit Tracker
$24 One-Time Download
Unlocked Formulas
Download Pro Workbook ($24) →
Works in Microsoft Excel, Google Sheets & Apple Numbers
Topics: screened topsoil, garden loam / planting mix, aggregate comparison, gravel density
Open Aggregate Material Calculator →

Related Material Comparisons Guides

Material Comparisons

Crusher Run (#411) vs. #57 Crushed Stone: Which Aggregate Should You Order?

Understand the critical engineering difference between clean washed #57 angular stone and dense-graded Crusher Run (Item #4 / Quarry Process) before ordering bulk delivery.

Material Comparisons

#57 Crushed Stone vs. Pea Gravel: Density, Cost & Best Uses Compared (2026 Guide)

Side-by-side engineering comparison of #57 Crushed Stone and Pea Gravel, covering bulk density (1.35 T/yd³ vs 1.28 T/yd³), price per ton, compaction lock, and drainage performance.

Material Comparisons

Crusher Run (#411) vs. Road Base (Class 2 ABC): Density, Cost & Best Uses Compared (2026 Guide)

Side-by-side engineering comparison of Crusher Run (#411) and Road Base (Class 2 ABC), covering bulk density (1.48 T/yd³ vs 1.50 T/yd³), price per ton, compaction lock, and drainage performance.

Material Comparisons

Decomposed Granite (DG) vs. Pea Gravel: Density, Cost & Best Uses Compared (2026 Guide)

Side-by-side engineering comparison of Decomposed Granite (DG) and Pea Gravel, covering bulk density (1.46 T/yd³ vs 1.28 T/yd³), price per ton, compaction lock, and drainage performance.

Material Comparisons

Crushed Limestone vs. Crushed Granite: Density, Cost & Best Uses Compared (2026 Guide)

Side-by-side engineering comparison of Crushed Limestone and Crushed Granite, covering bulk density (1.38 T/yd³ vs 1.35 T/yd³), price per ton, compaction lock, and drainage performance.

Material Comparisons

Asphalt Millings vs. Crusher Run Gravel: Density, Cost & Best Uses Compared (2026 Guide)

Side-by-side engineering comparison of Asphalt Millings and Crusher Run Gravel, covering bulk density (1.25 T/yd³ vs 1.48 T/yd³), price per ton, compaction lock, and drainage performance.