← Back to All 330 Contractor Guides
Driveway & Base Guides Published 2026-10-11 8 min read By Burim Bekteshi · Senior Aggregate Editor

How Much Gravel for a 24x24 Driveway? (576 Sq Ft Tonnage & Cost Chart)

A 24 ft × 24 ft driveway (576 sq ft) requires 11.11 US short tons (7.82 cubic yards) of dense-graded driveway gravel at a standard 4-inch depth (including a 10% compaction allowance). For a 2-inch surface refresh, order 5.55 tons (3.91 yd³); for a 6-inch heavy-duty base, order 16.66 tons (11.73 yd³).

24x24 ft gravel driveway tonnage and layer depth diagram
24x24 ft gravel driveway tonnage and layer depth diagram
Position-0 Engineering Summary · 24' × 24' Driveway (576 Sq Ft)
How many tons and cubic yards of gravel do you need for a 24×24 driveway?

A 24 ft × 24 ft driveway (576 sq ft) requires 11.11 US short tons (7.82 cubic yards) of dense-graded driveway gravel at a standard 4-inch depth (including a 10% compaction allowance). For a 2-inch surface refresh, order 5.55 tons (3.91 yd³); for a 6-inch heavy-duty base, order 16.66 tons (11.73 yd³).

2" Top-Up Refresh5.55 Tons (3.91 yd³)
4" Standard Layer11.11 Tons (7.82 yd³)
6" Structural Base16.66 Tons (11.73 yd³)
Est. 4" Delivered Cost$495 – $773

Specification & Reference Table: Step-by-Step Volume & Tonnage Math for a 24 ft × 24 ft Driveway

Designing or resurfacing a 24-foot wide by 24-foot long (576 sq ft) generous two-car parking court starts with converting surface area and compacted lift thickness into cubic yards, then multiplying by the quarry bulk density of your chosen stone:

Exact Engineering Calculation (24' × 24' @ 4" Depth): 1. Surface Area = 24 ft × 24 ft = 576 sq ft
2. Net Volume (cu ft) = 576 sq ft × (4 in ÷ 12) = 192.00 cu ft
3. Net Volume (cu yd) = 192.00 cu ft ÷ 27 = 7.11 yd³
4. Net Quarry Weight = 7.11 yd³ × 1.42 tons/yd³ = 10.10 tons
5. Recommended Order (+10% Compaction Buffer) = 11.11 Tons (7.82 Cubic Yards)

24×24 Driveway Gravel Tonnage, Cubic Yards & Truckload Table (By Depth)

Use the lookup table below to compare material requirements for a 24' × 24' driveway across six common excavation and resurfacing depths (using 1.42 tons/yd³ dense-graded driveway stone with a 10% compaction allowance):

Compacted Depth Primary Application Net Cubic Yards Order Cubic Yards (+10%) Order Tons (+10%) Tandem Truck Loads (15T)
2 Inches (0.17 ft) Surface Top-Dress / Refresh (#57 or #8 Stone) 3.56 yd³ 3.91 yd³ 5.55 tons 1 load(s)
3 Inches (0.25 ft) Light Resurfacing / Wearing Course 5.33 yd³ 5.87 yd³ 8.33 tons 1 load(s)
4 Inches (0.33 ft) Standard Compacted Lift (Crusher Run / #411) 7.11 yd³ 7.82 yd³ 11.11 tons 1 load(s)
6 Inches (0.50 ft) Heavy-Duty Structural Base (Pickup & SUV Traffic) 10.67 yd³ 11.73 yd³ 16.66 tons 2 load(s)
8 Inches (0.67 ft) 2-Layer New Driveway (4" Sub-Base + 4" Top) 14.22 yd³ 15.64 yd³ 22.22 tons 2 load(s)
12 Inches (1.00 ft) Full 3-Layer Clay/Frost Excavation (6"+4"+2") 21.33 yd³ 23.47 yd³ 33.32 tons 3 load(s)

Bulk Density & Moisture Physics (a 24x24 Driveway): When ordering quarry materials or scheduling dump truck dispatch, understanding the difference between loose cubic yard volume and certified scale tonnage is critical. Standard open-graded crushed stone (such as washed ASTM #57, #67, or #8 stone) maintains a loose bulk density of 2,640 to 2,720 lbs per cubic yard (1.32 to 1.36 US short tons/yd³) with a 38%–40% void ratio. Dense-graded road bases containing stone dust fines (such as #411 Crusher Run, #304 Limestone, Item #4, or Caltrans Class 2 AB) pack tighter and weigh 2,920 to 3,000 lbs per cubic yard (1.46 to 1.50 US short tons/yd³). After stockpile rain events, retained surface moisture can increase scale ticket weight by 5% to 12% on stone and up to 20% on sand or screened topsoil.

Loose vs. Compacted Volume (12%–18% Shrinkage Factor): Every cubic yard table measures in-place geometric volume before mechanical compaction. Once you spread aggregate and make 3 to 4 passes with a 5,000-lb vibratory plate compactor or smooth-drum roller, angular particles rotate into void spaces and the lift thickness compresses by 12% to 18% (and up to 20% for Decomposed Granite or Crusher Run). Regional mineralogy also shifts yield: dolomitic limestone and granite average 1.35–1.48 tons/yd³, dense Pacific Northwest basalt reaches 1.52 tons/yd³, and porous volcanic scoria or lava rock weighs just 0.65–0.78 tons/yd³.

Material Grade Comparison & Contractor Installation Best Practices

Selecting the right aggregate gradation and sub-base assembly determines whether your installation stays laser-level for 20 years or ruts and pumps mud after the first freeze-thaw season. Compare the four primary contractor aggregate classes below:

Aggregate Class & Grade Bulk Density Compaction Buffer Optimal Lift Depth & Geotextile Pairing Primary Engineering Application
Dense-Graded Base (#411, #304, Item #4, Class 2 AB) 1.48 – 1.50 T/yd³ +15% 4"–6" lifts over woven stabilization fabric Driveway structural base, paver sub-base, parking lots
Open-Graded Washed Stone (ASTM #57, #67, #4) 1.32 – 1.36 T/yd³ +10% 3"–4" layer wrapped in 4 oz non-woven fabric French drains, shed pads, retaining wall backfill, concrete slabs
Fine Screed & Pathway Stone (#8, #89, Pea Gravel, DG) 1.32 – 1.46 T/yd³ +12% – 18% 1"–3" compacted or screeded top lift Patio walkways, permeable paver bedding, xeriscape beds
Heavy Sub-Base & Armor (#1, #2, #3 Ballast, Riprap) 1.28 – 1.30 T/yd³ +10% 6"–12" lift over heavy woven geotextile Soft clay stabilization, construction entrances, ditch erosion armor
  • Sub-Base Excavation & Organic Stripping: Always strip 100% of sod, roots, and spongy black topsoil down to firm mineral subsoil. Topsoil decomposes and holds water, causing gravel layers to sink unevenly.
  • Woven vs. Non-Woven Geotextile Fabric Selection: Roll out high-tensile woven stabilization geotextile (200–300 lb grab tensile) under driveways, parking pads, and road bases to separate clay from crushed stone. Use 4 oz to 6 oz needle-punched non-woven drainage fabric inside French drain trenches and behind retaining walls where high water permittivity is required.
  • Compaction in 4-Inch Maximum Lifts: Never dump 8 to 12 inches of Crusher Run or road base and attempt to compact it in a single pass. Spread and compact in 3-inch to 4-inch lifts at optimum moisture content (lightly misted with a garden hose so stone dust binds tightly without turning soupy).
  • Positive Drainage Slope & Edge Restraint: Grade driveways with a 2% to 3% center crown (1/4" to 3/8" drop per foot toward side ditches) and pitch patios 1/8" to 1/4" per foot away from building foundations. Secure decorative pea gravel or decomposed granite with steel, aluminum, or timber perimeter edging.
  • Common Ordering Mistakes to Avoid: Never order washed #57 stone for a steep sloped driveway without a compacted #304/#411 base (clean stone rolls on grades over 6%), never exceed half-ton pickup axle payload limits (1 cubic yard = 2,700 lbs), and always verify overhead tree/wire clearance (24–28 ft raised bed height) before dump truck arrival.
Customize Your 24' × 24' Driveway Estimate

Adjust Stone Type, Compaction Buffer & Local Quarry Price

Open our interactive Driveway Gravel Calculator to test #57 stone, Crusher Run, or Asphalt Millings for your 576 sq ft project.

Recommended 3-Layer Stone Split for a Brand-New 24×24 Driveway

If you are stripping topsoil down to firm subsoil to build a brand-new 24 ft × 24 ft driveway (8 inches total structural thickness), do not order a single grade of stone. Split your quarry order across two or three interlocking gradations:

  • Geotextile Underlayment: Roll out 663 sq ft of woven stabilization fabric (with 12-inch overlaps) so clay mud cannot pump upward into your stone.
  • Bottom Sub-Base Lift (4" Depth): Order 11.11 tons of coarse #3 Crushed Stone (1.5"–2.5") or heavy Crusher Run (#411 / Item #4) compacted with a vibratory roller.
  • Middle Drainage & Lock Lift (2" Depth): Order 5.55 tons of clean angular ASTM #57 Crushed Stone.
  • Top Wearing Course (2" Depth): Order 5.55 tons of 3/4"-minus Crusher Run with stone dust fines graded with a 2% center crown so rainwater sheets off toward the ditches.

Frequently Asked Questions

How many dump truck loads of gravel does a 24x24 driveway take?
At a 4-inch depth (11.11 tons), a 24×24 driveway requires 1 tandem-axle dump truck load(s) (at 15 tons per truck) or 2 single-axle dump truck load(s) (at 8 tons per truck).
How much does gravel cost for a 24x24 driveway in 2026?
Assuming $32–$52 per ton for crushed stone plus $140–$195 per dump truck delivery load, resurfacing a 24×24 driveway at 4 inches deep costs approximately $495 to $773 delivered for materials.
How do you calculate exact tons and cubic yards for a 24x24 Driveway?
Multiply your project length (ft) × width (ft) × depth (ft) and divide by 27 to get net cubic yards (yd³), or use the contractor shortcut Area (sq ft) × Depth (in) ÷ 324 = Cubic Yards. Multiply cubic yards by the material bulk density (1.35 tons/yd³ for washed #57 or pea stone; 1.48 tons/yd³ for Crusher Run or road base) and add a 10% to 15% compaction buffer.
How much area does 1 ton or 1 cubic yard cover for a 24x24 Driveway?
One cubic yard (27 cu ft) covers 324 sq ft at 1" deep, 162 sq ft at 2" deep, 108 sq ft at 3" deep, 81 sq ft at 4" deep, and 54 sq ft at 6" deep. Because 1 US short ton (2,000 lbs) of standard gravel equals approximately 0.74 cubic yards (20 cu ft), 1 ton covers 120 sq ft at 2" deep, 80 sq ft at 3" deep, or 60 sq ft at 4" deep.
PRO CONTRACTOR & HARDSCAPE TAKEOFF BUNDLE EXCEL (.XLSX) + GOOGLE SHEETS

Need Multi-Layer Takeoffs, Client PDF Proposals & Job Costing in Excel / Google Sheets?

Upgrade to the Pro Excavation, Hardscape & Aggregate Bid Workbook (Excel + Google Sheets)—engineered for contractors, landscapers, and estimators who want instant multi-layer assemblies, dirt spoils hauling math, crew labor markups, and printable client bid sheets.

01. Multi-Layer Driveway & Patio Assembly Takeoff
02. Excavation Spoils & Dump Truck Hauling Optimizer
03. French Drain & Retaining Wall Calculator
04. Crew Loaded Labor & Overhead Markup Calculator
05. Quarry & Supplier Price Book (VLOOKUP)
06. Client-Ready Printable Bid Proposal
07. Material Order & Dispatch Checklist
08. 12-Month Job Costing & Profit Tracker
$24 One-Time Download
Unlocked Formulas
Download Pro Workbook ($24) →
Works in Microsoft Excel, Google Sheets & Apple Numbers
Topics: 24x24 driveway gravel, how much gravel for 24x24 driveway, 576 sq ft driveway tons, crusher run
Open Driveway Gravel Calculator →

Related Driveway & Base Guides

Driveway & Base Guides

How Much Gravel Do I Need for a Driveway? Complete 2026 Tonnage & Layer Guide

Learn how to calculate exact cubic yards and tons of gravel for single-car, double-car, and rural driveways using the 3-layer sub-base, mid-layer, and surface stone method.

Driveway & Base Guides

How Much Gravel for a 10x20 Driveway? (200 Sq Ft Tonnage & Cost Chart)

Exact gravel tonnage, cubic yards, dump truck loads, and 3-layer excavation specs for a 10 ft × 20 ft (200 sq ft) single-car parking pad.

Driveway & Base Guides

How Much Gravel for a 10x30 Driveway? (300 Sq Ft Tonnage & Cost Chart)

Exact gravel tonnage, cubic yards, dump truck loads, and 3-layer excavation specs for a 10 ft × 30 ft (300 sq ft) short single-lane driveway.

Driveway & Base Guides

How Much Gravel for a 10x40 Driveway? (400 Sq Ft Tonnage & Cost Chart)

Exact gravel tonnage, cubic yards, dump truck loads, and 3-layer excavation specs for a 10 ft × 40 ft (400 sq ft) 10-foot residential driveway.

Driveway & Base Guides

How Much Gravel for a 10x50 Driveway? (500 Sq Ft Tonnage & Cost Chart)

Exact gravel tonnage, cubic yards, dump truck loads, and 3-layer excavation specs for a 10 ft × 50 ft (500 sq ft) single-car residential driveway.

Driveway & Base Guides

How Much Gravel for a 10x60 Driveway? (600 Sq Ft Tonnage & Cost Chart)

Exact gravel tonnage, cubic yards, dump truck loads, and 3-layer excavation specs for a 10 ft × 60 ft (600 sq ft) setback residential driveway.