A 18 ft × 40 ft driveway (720 sq ft) requires 13.88 US short tons (9.78 cubic yards) of dense-graded driveway gravel at a standard 4-inch depth (including a 10% compaction allowance). For a 2-inch surface refresh, order 6.94 tons (4.89 yd³); for a 6-inch heavy-duty base, order 20.83 tons (14.67 yd³).
Specification & Reference Table: Step-by-Step Volume & Tonnage Math for a 18 ft × 40 ft Driveway
Designing or resurfacing a 18-foot wide by 40-foot long (720 sq ft) two-car garage driveway starts with converting surface area and compacted lift thickness into cubic yards, then multiplying by the quarry bulk density of your chosen stone:
2. Net Volume (cu ft) = 720 sq ft × (4 in ÷ 12) = 240.00 cu ft
3. Net Volume (cu yd) = 240.00 cu ft ÷ 27 = 8.89 yd³
4. Net Quarry Weight = 8.89 yd³ × 1.42 tons/yd³ = 12.62 tons
5. Recommended Order (+10% Compaction Buffer) = 13.88 Tons (9.78 Cubic Yards)
18×40 Driveway Gravel Tonnage, Cubic Yards & Truckload Table (By Depth)
Use the lookup table below to compare material requirements for a 18' × 40' driveway across six common excavation and resurfacing depths (using 1.42 tons/yd³ dense-graded driveway stone with a 10% compaction allowance):
| Compacted Depth | Primary Application | Net Cubic Yards | Order Cubic Yards (+10%) | Order Tons (+10%) | Tandem Truck Loads (15T) |
|---|---|---|---|---|---|
| 2 Inches (0.17 ft) | Surface Top-Dress / Refresh (#57 or #8 Stone) | 4.44 yd³ | 4.89 yd³ | 6.94 tons | 1 load(s) |
| 3 Inches (0.25 ft) | Light Resurfacing / Wearing Course | 6.67 yd³ | 7.33 yd³ | 10.41 tons | 1 load(s) |
| 4 Inches (0.33 ft) | Standard Compacted Lift (Crusher Run / #411) | 8.89 yd³ | 9.78 yd³ | 13.88 tons | 1 load(s) |
| 6 Inches (0.50 ft) | Heavy-Duty Structural Base (Pickup & SUV Traffic) | 13.33 yd³ | 14.67 yd³ | 20.83 tons | 2 load(s) |
| 8 Inches (0.67 ft) | 2-Layer New Driveway (4" Sub-Base + 4" Top) | 17.78 yd³ | 19.56 yd³ | 27.77 tons | 2 load(s) |
| 12 Inches (1.00 ft) | Full 3-Layer Clay/Frost Excavation (6"+4"+2") | 26.67 yd³ | 29.33 yd³ | 41.65 tons | 3 load(s) |
Bulk Density & Moisture Physics (a 18x40 Driveway): When ordering quarry materials or scheduling dump truck dispatch, understanding the difference between loose cubic yard volume and certified scale tonnage is critical. Standard open-graded crushed stone (such as washed ASTM #57, #67, or #8 stone) maintains a loose bulk density of 2,640 to 2,720 lbs per cubic yard (1.32 to 1.36 US short tons/yd³) with a 38%–40% void ratio. Dense-graded road bases containing stone dust fines (such as #411 Crusher Run, #304 Limestone, Item #4, or Caltrans Class 2 AB) pack tighter and weigh 2,920 to 3,000 lbs per cubic yard (1.46 to 1.50 US short tons/yd³). After stockpile rain events, retained surface moisture can increase scale ticket weight by 5% to 12% on stone and up to 20% on sand or screened topsoil.
Loose vs. Compacted Volume (12%–18% Shrinkage Factor): Every cubic yard table measures in-place geometric volume before mechanical compaction. Once you spread aggregate and make 3 to 4 passes with a 5,000-lb vibratory plate compactor or smooth-drum roller, angular particles rotate into void spaces and the lift thickness compresses by 12% to 18% (and up to 20% for Decomposed Granite or Crusher Run). Regional mineralogy also shifts yield: dolomitic limestone and granite average 1.35–1.48 tons/yd³, dense Pacific Northwest basalt reaches 1.52 tons/yd³, and porous volcanic scoria or lava rock weighs just 0.65–0.78 tons/yd³.
Material Grade Comparison & Contractor Installation Best Practices
Selecting the right aggregate gradation and sub-base assembly determines whether your installation stays laser-level for 20 years or ruts and pumps mud after the first freeze-thaw season. Compare the four primary contractor aggregate classes below:
| Aggregate Class & Grade | Bulk Density | Compaction Buffer | Optimal Lift Depth & Geotextile Pairing | Primary Engineering Application |
|---|---|---|---|---|
| Dense-Graded Base (#411, #304, Item #4, Class 2 AB) | 1.48 – 1.50 T/yd³ | +15% | 4"–6" lifts over woven stabilization fabric | Driveway structural base, paver sub-base, parking lots |
| Open-Graded Washed Stone (ASTM #57, #67, #4) | 1.32 – 1.36 T/yd³ | +10% | 3"–4" layer wrapped in 4 oz non-woven fabric | French drains, shed pads, retaining wall backfill, concrete slabs |
| Fine Screed & Pathway Stone (#8, #89, Pea Gravel, DG) | 1.32 – 1.46 T/yd³ | +12% – 18% | 1"–3" compacted or screeded top lift | Patio walkways, permeable paver bedding, xeriscape beds |
| Heavy Sub-Base & Armor (#1, #2, #3 Ballast, Riprap) | 1.28 – 1.30 T/yd³ | +10% | 6"–12" lift over heavy woven geotextile | Soft clay stabilization, construction entrances, ditch erosion armor |
- Sub-Base Excavation & Organic Stripping: Always strip 100% of sod, roots, and spongy black topsoil down to firm mineral subsoil. Topsoil decomposes and holds water, causing gravel layers to sink unevenly.
- Woven vs. Non-Woven Geotextile Fabric Selection: Roll out high-tensile woven stabilization geotextile (200–300 lb grab tensile) under driveways, parking pads, and road bases to separate clay from crushed stone. Use 4 oz to 6 oz needle-punched non-woven drainage fabric inside French drain trenches and behind retaining walls where high water permittivity is required.
- Compaction in 4-Inch Maximum Lifts: Never dump 8 to 12 inches of Crusher Run or road base and attempt to compact it in a single pass. Spread and compact in 3-inch to 4-inch lifts at optimum moisture content (lightly misted with a garden hose so stone dust binds tightly without turning soupy).
- Positive Drainage Slope & Edge Restraint: Grade driveways with a 2% to 3% center crown (1/4" to 3/8" drop per foot toward side ditches) and pitch patios 1/8" to 1/4" per foot away from building foundations. Secure decorative pea gravel or decomposed granite with steel, aluminum, or timber perimeter edging.
- Common Ordering Mistakes to Avoid: Never order washed #57 stone for a steep sloped driveway without a compacted #304/#411 base (clean stone rolls on grades over 6%), never exceed half-ton pickup axle payload limits (1 cubic yard = 2,700 lbs), and always verify overhead tree/wire clearance (24–28 ft raised bed height) before dump truck arrival.
Adjust Stone Type, Compaction Buffer & Local Quarry Price
Open our interactive Driveway Gravel Calculator to test #57 stone, Crusher Run, or Asphalt Millings for your 720 sq ft project.
Recommended 3-Layer Stone Split for a Brand-New 18×40 Driveway
If you are stripping topsoil down to firm subsoil to build a brand-new 18 ft × 40 ft driveway (8 inches total structural thickness), do not order a single grade of stone. Split your quarry order across two or three interlocking gradations:
- Geotextile Underlayment: Roll out 828 sq ft of woven stabilization fabric (with 12-inch overlaps) so clay mud cannot pump upward into your stone.
- Bottom Sub-Base Lift (4" Depth): Order 13.88 tons of coarse #3 Crushed Stone (1.5"–2.5") or heavy Crusher Run (#411 / Item #4) compacted with a vibratory roller.
- Middle Drainage & Lock Lift (2" Depth): Order 6.94 tons of clean angular ASTM #57 Crushed Stone.
- Top Wearing Course (2" Depth): Order 6.94 tons of 3/4"-minus Crusher Run with stone dust fines graded with a 2% center crown so rainwater sheets off toward the ditches.
Frequently Asked Questions
How many dump truck loads of gravel does a 18x40 driveway take?
How much does gravel cost for a 18x40 driveway in 2026?
How do you calculate exact tons and cubic yards for a 18x40 Driveway?
Area (sq ft) × Depth (in) ÷ 324 = Cubic Yards. Multiply cubic yards by the material bulk density (1.35 tons/yd³ for washed #57 or pea stone; 1.48 tons/yd³ for Crusher Run or road base) and add a 10% to 15% compaction buffer.